Tucson Superior Concrete provides concrete demolition and removal in Tucson, AZ, for driveways, patios, pool decks, sidewalks, slabs, foundations, and commercial concrete. Our crews saw-cut, break, load, and haul away unwanted concrete with equipment selected for the project's access and reinforcement. When replacement is planned, we can coordinate removal with a new driveway, patio, slab, foundation, or other concrete installation. That keeps demolition and the follow-on pour within one concrete-focused scope.
Caliche soil, expansive clay, monsoon flooding, and 110-degree heat cycles can leave Tucson concrete heaved, cracked, or settled beyond practical repair. Controlled cuts and sectional breaking help protect block walls, irrigation lines, pool equipment, and neighboring hardscape. We check slab thickness, reinforcement, access, and nearby utilities before choosing the removal method. Earth-disturbing work is handled with Pima County Department of Environmental Quality dust-control requirements in mind because Tucson sits in a PM10 nonattainment area.
Concrete removal in the Tucson market runs about $2 to $8 per square foot depending on slab thickness, reinforcement, and access. A standard 4-inch residential slab averages around $4.35 per square foot, with most quotes between $3.49 and $5.21 per square foot. Disposal commonly adds $51 to $100 per ton, while equipment and crew time typically runs $15 to $40 per ton.
Tucson Superior Concrete provides concrete demolition and removal throughout Tucson, Oro Valley, Marana, Sahuarita, and the greater Pima County metro area.
Concrete demolition and removal is the controlled process of separating unwanted concrete from surfaces that will remain, breaking it into manageable pieces, loading the debris, and hauling it away. The scope may be a single cracked walkway section or a full commercial slab tear-out.
Thickness and reinforcement determine how the work is planned. A residential driveway is typically a 4-inch pour, while structural slabs, foundations, and older sidewalks in Tucson's historic Barrio neighborhoods may run 5 to 6 inches with heavier reinforcement.
Before breaking begins, the crew identifies clean cut lines, nearby utilities, equipment access, and anything that needs protection. The cleared area can then be graded and compacted so it is ready for a replacement pour without leaving unstable base material behind.
A planned tear-out does more than clear old concrete. It protects the surrounding property, handles debris responsibly, and leaves a dependable starting point for the next phase of work.
Each removal plan is matched to the concrete, reinforcement, access, and nearby property features. Tucson Superior Concrete handles residential and commercial tear-outs from small walkway sections to driveways, pool decks, foundations, and larger slabs.
Most Tucson residential driveways run 400 to 700 square feet. We saw-cut clean boundaries at the garage slab or street apron, break and load the driveway, and remove the debris without damaging concrete the owner plans to keep.
Request Estimate
Patio and pool-deck removal is performed in controlled sections around coping, the pool shell, and buried plumbing or electrical. Smaller break sections limit shock transfer to the pool structure and help protect nearby hardscape.
Request Estimate
Slab removal can cover a shed pad, addition slab, or larger flatwork area. As a pricing example from the draft, a 20-by-20 slab measuring 400 square feet is estimated at $1,400 to $2,100 for removal, with a typical disposal fee of $500 to $1,000.
Request Estimate
Foundations and footings require heavier breaking because the concrete is thicker, more heavily reinforced, and often followed by deeper excavation. Removal depth is coordinated with the geotechnical requirements of the residential addition or commercial redevelopment planned next.
Request Estimate
Walkway removal may involve one failed section or a longer run of older concrete. Careful saw-cutting separates the tear-out from street aprons, steps, landscaping edges, and adjacent slabs before breaking starts.
Request Estimate
Commercial work ranges from reinforced slabs to parking structures and redevelopment foundations. The crew matches compact or full-size hydraulic equipment, loading capacity, and haul-out logistics to the slab and the available access.
Request EstimateThe right removal method depends on more than square footage. Thickness, reinforcement, decorative finishes, access, nearby structures, disposal weight, and the intended replacement all affect equipment, labor, cost, and schedule.
Standard driveways and patios are often the most direct projects when equipment and trailers can reach the work area. Their price and timing still depend on actual thickness, reinforcement, and disposal weight.
Structural concrete and older flatwork demand more breaking and loading than a standard slab. Probing or core sampling when needed helps confirm the thickness before the equipment and crew plan is finalized.
Side yards, enclosed backyards, and closely built Tucson lots can limit the size of equipment used. Access is checked during the site visit so the plan accounts for loading, truck position, and protection of nearby property.
Stamped concrete needs a more deliberate tear-out when decorative sections nearby will remain. The patterned surface may sit over a thicker base, an integral color layer, or added reinforcement mesh.
Large slabs, foundations, and footings combine concrete thickness, reinforcement, disposal weight, and excavation requirements. These projects call for a larger equipment and haul-out plan than a typical residential flatwork removal.
A useful demolition plan begins with the slab rather than a one-size-fits-all method. The crew evaluates square footage, thickness, reinforcement, access, nearby utilities and structures, haul-out logistics, and whether the area will receive a new pour.
Every quote starts with an on-site walk to measure the slab, confirm access, and check thickness with a probe or core sample when needed. That review supports a firm estimate instead of a rough phone number, with no cost or obligation to obtain it.
Work is performed under Arizona Registrar of Contractors licensing, and crews carry general liability coverage on every job site. That accountability matters when a hydraulic breaker may operate 10 feet from a block wall, pool shell, or neighboring property line.
Diamond-blade saws create clean boundaries, hydraulic breakers and jackhammers reduce slabs, and skid steers load debris into appropriately sized dump trailers. Equipment is matched to conditions ranging from a tight backyard to a commercial foundation.
Tucson Superior Concrete assesses slab thickness using American Concrete Institute guidance, plans dust control around Pima County requirements, and hauls debris to an approved recycling or disposal facility. When a new driveway, patio, or slab is next, demolition and installation can be coordinated as one project.
Get a Free EstimateCaliche soil, expansive clay, flash flooding during monsoons, and extreme heat cycles can make slabs move unevenly. Demolition becomes appropriate when heaving, cracking, or settlement leaves concrete unsuitable for the planned use or replacement.
A slab that contains rebar, mesh, or greater-than-expected thickness takes more time and heavier equipment to break and load. Confirming those conditions before work begins reduces surprises in the crew, schedule, and haul-out plan.
Narrow access can prevent a full-size machine or trailer from reaching the slab. A compact skid steer, smaller breaking equipment, and a carefully planned loading route may be needed for backyard patios and other confined areas.
Block walls, garage slabs, street aprons, irrigation lines, and neighboring concrete can sit close to the tear-out. Saw-cut boundaries and controlled breaking help keep vibration and cracking away from features that remain.
Pool decking is close to coping, the pool shell, and buried plumbing and electrical serving the equipment. Breaking the deck in controlled sections helps avoid transferring unnecessary shock to the pool structure.
Uncontrolled demolition can leave debris piles, uncompacted base, and excessive dust. Water suppression, compliant haul-away, and grading and compaction after removal prepare the area for a cleaner next phase.
The removal sequence is planned to protect utilities, surrounding surfaces, and the area beneath the slab. From the first measurement through final compaction, each step prepares the site for safe access and the intended replacement.
The crew measures square footage, checks slab thickness, identifies reinforcement, notes nearby property features, and confirms access for breakers, skid steers, trucks, and trailers.
Arizona 811 is contacted before excavation-adjacent demolition so buried lines can be marked. For larger jobs disturbing significant ground area, the required Pima County Department of Environmental Quality dust-control permit is filed before the scheduled start.
Diamond-blade saws create straight break lines against garage slabs, street aprons, or concrete that will remain. Water suppression controls dust while the cut helps prevent spalling and unplanned cracks.
Hydraulic breakers or jackhammers reduce the slab in sections sized for the site and equipment. The crew works deliberately around walls, hardscape, pools, and other features that need protection.
Skid steers load the broken concrete into dump trailers selected for the property access and project scale. Debris is then taken to a Pima County-approved recycling or disposal facility.
After the concrete is removed, the exposed base is cleared, graded, and compacted. That leaves a more stable surface for a replacement driveway, patio, slab, or other planned construction.
Schedule an on-site review to measure the concrete, evaluate thickness and access, and discuss haul-away and any replacement work. The estimate is provided with no cost or obligation.
These answers cover Tucson concrete removal costs, timing, site preparation, equipment, and disposal. A site visit is still needed to account for the actual slab, reinforcement, access, and nearby property features.
Call Our Concrete TeamConcrete removal in the Tucson market runs about $2 to $8 per square foot depending on thickness, reinforcement, and access. A standard 4-inch residential slab averages around $4.35 per square foot, with most quotes between $3.49 and $5.21 per square foot.
Square footage, slab thickness, rebar or mesh, equipment access, nearby surfaces, and disposal weight all affect the estimate. Stamped concrete, tight side yards, second-story pool decks, and heavily reinforced foundations generally require more labor or specialized planning.
A roughly 500-square-foot single-car driveway is estimated at $1,750 to $2,600 for demolition and haul-away, plus disposal of about $50 to $100 per ton. Double-car and extended driveways can reach $3,000 to $4,500 when thicker approaches and additional disposal weight are involved.
A standard driveway or patio removal is a same-day job in most cases. Larger slabs, foundations, or heavily reinforced concrete may take one to three days depending on square footage and access.
A residential driveway is typically a 4-inch pour. Structural slabs, foundations, and older sidewalks in Tucson's historic Barrio neighborhoods may run 5 to 6 inches with heavier reinforcement.
The crew saw-cuts a clean boundary with diamond blades where removal meets a garage slab, street apron, or adjacent section. Water suppression controls dust, while the straight cut helps prevent spalling and unintended cracking.
Arizona 811 is contacted before excavation-adjacent demolition so buried lines can be marked. The site assessment also identifies irrigation, pool equipment, and other nearby systems that need protection.
Diamond-blade cutting uses water suppression to control dust at the cut. Larger jobs that disturb significant ground area are planned around the required Pima County Department of Environmental Quality dust-control permit because Tucson is in a PM10 nonattainment area.
Skid steers load the debris into dump trailers sized for the site's access and project scale. The concrete is hauled to a Pima County-approved recycling or disposal facility.
Stamped concrete typically adds 15 to 25 percent to labor time compared with plain broom-finish concrete. A thicker base, integral color layer, reinforcement mesh, and the need to preserve adjacent decorative sections can all add work.
Yes. Foundation and footing removal involves thicker concrete, heavier rebar, and often deeper excavation, so the equipment and haul-out plan is larger than for standard flatwork. Removal depth is coordinated with the geotechnical requirements of what will be built next.
Pool decks are broken in controlled sections around the shell, coping, and buried plumbing and electrical. This approach is intended to limit shock transfer to the pool structure while the decking is removed.
The site visit includes measuring square footage, checking thickness with a probe or core sample when needed, and confirming truck access for haul-out. That review supports a firm number rather than a rough phone estimate, and there is no cost or obligation.
